qmk-firmware/keyboard/ergodox_ez/Makefile

115 lines
3.6 KiB
Makefile
Raw Normal View History

2015-10-26 20:32:37 +00:00
#----------------------------------------------------------------------------
# On command line:
#
# make = Make software.
2015-10-26 20:32:37 +00:00
#
# make clean = Clean out built project files.
#
# That's pretty much all you need. To compile, always go make clean,
# followed by make.
2015-10-26 20:32:37 +00:00
#
# For advanced users only:
2015-10-26 20:32:37 +00:00
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = ergodox_ez
2015-10-26 20:32:37 +00:00
# Directory common source filess exist
TOP_DIR = ../..
TMK_DIR = ../../tmk_core
2015-10-26 20:32:37 +00:00
# Directory keyboard dependent files exist
TARGET_DIR = .
# # project specific files
SRC = ergodox_ez.c \
2015-10-28 02:07:15 +00:00
twimaster.c \
matrix.c
2015-10-26 20:32:37 +00:00
ifdef KEYMAP
2016-01-22 01:51:59 +00:00
SRC := keymaps/$(KEYMAP)/keymap.c $(SRC)
2015-10-26 20:32:37 +00:00
else
2016-01-22 01:51:59 +00:00
SRC := keymaps/default/keymap.c $(SRC)
2015-10-26 20:32:37 +00:00
endif
CONFIG_H = config.h
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
2015-10-28 02:07:15 +00:00
OPT_DEFS += -DBOOTLOADER_SIZE=512
2015-10-26 20:32:37 +00:00
# Build Options
# comment out to disable the options.
#
2015-10-28 02:07:15 +00:00
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
# CONSOLE_ENABLE = yes # Console for debug(+400)
2015-10-28 02:07:15 +00:00
COMMAND_ENABLE = yes # Commands for debug and configuration
CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDox EZ
SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
# MIDI_ENABLE = yes # MIDI controls
# UNICODE_ENABLE = yes # Unicode
2015-10-26 20:32:37 +00:00
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
VPATH += $(TMK_DIR)
2015-10-26 20:32:37 +00:00
2015-10-27 18:33:18 +00:00
include $(TOP_DIR)/quantum/quantum.mk
2015-10-26 20:32:37 +00:00