V-USB: Consolidate usbconfig.h's into a single file (#8584)
This commit is contained in:
Ryan
GitHub
parent
8566a684bc
commit
51a81813b0
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,353 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
// max power draw with maxed white underglow measured at 120 mA (peaks)
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,353 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
|
|
@ -1,342 +0,0 @@
|
|||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,342 +0,0 @@
|
|||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU / 1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,342 +0,0 @@
|
|||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU / 1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,336 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 0
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
// /* #define USB_INTR_CFG_CLR 0 */
|
||||
// /* #define USB_INTR_ENABLE EIMSK */
|
||||
// #define USB_INTR_ENABLE_BIT INT1
|
||||
// /* #define USB_INTR_PENDING EIFR */
|
||||
// #define USB_INTR_PENDING_BIT INTF1
|
||||
// #define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,352 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -1,355 +0,0 @@
|
|||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
|
|
@ -1,342 +0,0 @@
|
|||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU / 1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
|
@ -10,7 +10,7 @@
|
|||
|
||||
#pragma once
|
||||
|
||||
#include "config.h"
|
||||
// clang-format off
|
||||
|
||||
/*
|
||||
General Description:
|
||||
Loading…
Reference in New Issue