qmk-firmware/keyboards/kbdfans/kbd8x/rules.mk
MechMerlin b49dbf9b19 [Keyboard] Create KBDFans directory (#5025)
* move over kbd19x into the kbdfans directory

* move over kbd4x into the kbdfans directory

* move kbd66 into the kbdfans directory

* move the kbd6x into the kbdfans directory

* move kbd8x into the kbdfans directory

* move kbd75 into the kbdfans directory

* move kbd67 into kbdfans directory

* add a fairly sparse readme for kbdfans directory

* update make instructions for keyboards and add the Complete Newbs Guide to readmes that was missing it

* get kbd75 compiling again

* remove repetitive #defines of KC_NO and KC_TRNS when QMK_KEYBOARD_H is already included in KBD75

* add links to kbdfans readme

* fix some readme formatting

* there is no reason to have two different keymaps with such a small difference, condensing to one

* turning on backlights by default

* enable backlight by default for kbd66

* noticed that the kbd75 had caps lock led code in every keymap. Moved it out to the keyboard.c so everyone can partake.

* Update keyboards/kbdfans/kbd66/readme.md

Co-Authored-By: mechmerlin <30334081+mechmerlin@users.noreply.github.com>

* update readme link ordering
2019-02-04 10:29:04 -08:00

70 lines
2.9 KiB
Makefile

# MCU name
#MCU = at90usb1286
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality on B7 by default
RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches