qmk-firmware/quantum/split_common/serial.h
James Churchill 28929ad017 Simplify split_common Code significantly (#4772)
* Eliminate separate slave loop

Both master and slave run the standard keyboard_task main loop now.

* Refactor i2c/serial specific code

Simplify some of the preprocessor mess by using common function names.

* Fix missing #endif

* Move direct pin mapping support from miniaxe to split_common

For boards with more pins than sense--sorry, switches.

* Reordering and reformatting only

* Don't run matrix_scan_quantum on slave side

* Clean up the offset/slaveOffset calculations

* Cut undebounced matrix size in half

* Refactor debouncing

* Minor fixups

* Split split_common transport and debounce code into their own files

Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes

* Refactor debounce for non-split keyboards too

* Update handwired/xealous to build using new split_common

* Fix debounce breaking basic test

* Dodgy method to allow a split kb to only include one of i2c/serial

SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.

SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code

if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.

This could be better but it would require explicitly updating all the
existing split keyboards.

* Enable LTO to get lets_split/sockets under the line

* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE

* Remove avr-specific sei() from split matrix_setup

Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().

* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.

* Add comments and fix formatting.
2019-01-17 10:08:14 -08:00

63 lines
2.1 KiB
C

#pragma once
#include <stdbool.h>
// /////////////////////////////////////////////////////////////////
// Need Soft Serial defines in config.h
// /////////////////////////////////////////////////////////////////
// ex.
// #define SOFT_SERIAL_PIN ?? // ?? = D0,D1,D2,D3,E6
// OPTIONAL: #define SELECT_SOFT_SERIAL_SPEED ? // ? = 1,2,3,4,5
// // 1: about 137kbps (default)
// // 2: about 75kbps
// // 3: about 39kbps
// // 4: about 26kbps
// // 5: about 20kbps
//
// //// USE simple API (using signle-type transaction function)
// /* nothing */
// //// USE flexible API (using multi-type transaction function)
// #define SERIAL_USE_MULTI_TRANSACTION
//
// /////////////////////////////////////////////////////////////////
// Soft Serial Transaction Descriptor
typedef struct _SSTD_t {
uint8_t *status;
uint8_t initiator2target_buffer_size;
uint8_t *initiator2target_buffer;
uint8_t target2initiator_buffer_size;
uint8_t *target2initiator_buffer;
} SSTD_t;
#define TID_LIMIT( table ) (sizeof(table) / sizeof(SSTD_t))
// initiator is transaction start side
void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size);
// target is interrupt accept side
void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size);
// initiator resullt
#define TRANSACTION_END 0
#define TRANSACTION_NO_RESPONSE 0x1
#define TRANSACTION_DATA_ERROR 0x2
#define TRANSACTION_TYPE_ERROR 0x4
#ifndef SERIAL_USE_MULTI_TRANSACTION
int soft_serial_transaction(void);
#else
int soft_serial_transaction(int sstd_index);
#endif
// target status
// *SSTD_t.status has
// initiator:
// TRANSACTION_END
// or TRANSACTION_NO_RESPONSE
// or TRANSACTION_DATA_ERROR
// target:
// TRANSACTION_DATA_ERROR
// or TRANSACTION_ACCEPTED
#define TRANSACTION_ACCEPTED 0x8
#ifdef SERIAL_USE_MULTI_TRANSACTION
int soft_serial_get_and_clean_status(int sstd_index);
#endif